MINI-Z EVO Kyosho FHSS KT-531P KT-432P (MR-03EVO/MA-030EVO) Receiver Conversion Receiver Module [MXO RACING] EVO-RX-KYFHSS

MINI-Z EVO Kyosho FHSS KT-531P KT-432P (MR-03EVO/MA-030EVO) Receiver Conversion Receiver Module [MXO RACING] EVO-RX-KYFHSS

This is the receiver for KYOSHO MR-03EVO and MA-030EVO
it can be used for KYOSHO Transmitter KT-531P, KT-432P

 

The MX EVO RX - KYFHSS is a KYOSHO FHSS compatible ultra - miniature receiver for KYOSHO's MR -03EVO and MA -030EVO , with an output speed of up to 1 . 925ms in EVO mode . It can work not only in EVO mode , but also in 4CH PWM standard signal mode .
In addition , we are developing miniature sensor brushless ESCs and other related products that can be directly mounted on this receiver .

Features ：
Size: 13 . 5*10 . 0*3 . 5mm;
Weight: 0 . 58g;
Working voltage: 3 . 0V or 3 . 3V;
Compatible with KYOSHO FHSS protoco(KT -531P , KT -432P)l;
Support EVO and 4CH PWM two working modes;
The output speed in EVO mode is 1 . 925ms;
The output speed in 4CH PWM mode is 3 . 85ms;
Support online firmware upgrade .

Bind Operation:
Install the MX EVO RX first , then power on the receiver and press the BIND switch until the red LED on the RX changes from slow flashing to fast flashing , and then proceed according to the BIND operation requirements of the transmitter . When the red LED on the RX changes from fast When the blinking turns to steady light , it means BIND is successful and the signal has been received .
Red LED status indication:
The red LED on the MX EVO RX is an indication of the working status of the RX:
1) When the red LED flashes slowly , it means that RX is waiting to receive a signal;
2) When the red LED flashes quickly , it means RX is in BIND mode;
3) When the red LED is always on , it means that the RX has received the signal stably .

Green LED status indication:
The green LED on the MX EVO RX is an indication of the RX operating mode:
1) When the green LED is on , it means the RX is working in EVO mode;
2) When the green LED is off , it means that the RX is working in 4CH PWM mode;
 
How to set up the transmitter (when MX EVO RX is used on MR -03EVO/MA -03EVO):
Because the brushless ESCs and servos on MR -03EVO/MA -03EVO cannot set the midpoint and end point , the user can only set the transmitter to adapt to the parameters of MR -03EVO/MA -03EVO . The settings are as follows:
1）TH TYPE    >   F5 : B5
2）EAP: ST >L150% R150%
                TH >H150% B150%
3）D/R:  ST >100%
                TH >100%
4）REV: ST >REV
               TH >REV
 
Note: Points 2 and 3 can be adjusted according to user habits .

How the MX EVO RX works in EVO mode:
When users install MX EVO RX on KYOSHO's MR -03EVO/MA -030EVO frame or other products that support EVO mode , MX EVO RX will work in EVO mode .
In EVO mode , when the MX EVO RX is just powered on , the LED on the RX will not flash quickly , but the green LED will light up .

Note: When using the MX EVO RX on the MR -03EVO/MA -03EVO , be sure to install it in place , otherwise you may burn it; if necessary , place the receiver compartment cover on the MR -03EVO/ MA -030EVO Add a small piece of sponge to hold down the MX EVO RX .